待解决问题
思科2600路由器V35业务开通
离问题结束还有0天0小时  |  提问者:sun_gwtt   |  提问时间:2013-10-25 08:27
先说组网 S2600---V35光猫--------PDH光端机---E1----SDH-----省总行路由器(思科型号未知) 全程开通后,业务不通,本地S2600设备物理接口UP,协议接口DOWN,从V35光猫向省行侧环回,省行可以看到环回,而向S2600环回,看不到环回,V35光猫、连接线缆、S2600路由器均更换过,基本可以排除硬件问题。由于本人不熟悉S2600配置,因此怀疑是S2600配置问题。 1、据总行客户反映,V35业务使用HDLC封装,V35是非帧,2M带宽。地市侧S3600无需配置其他信息,在serial 1/3口配置 一个iP 地址即可,查看running config 如下:只在serial1/3接口下存在一个IP地址:ip address 144.32.248.210 255.255.255.252 再无其他配置。 2、进入serial1/3接口查看端口信息如下: erial1/3 is up, line protocol is down Hardware is CD2430 in sync mode Description: line Internet address is 144.32.248.210/30 MTU 1500 bytes, [color=red]BW 128 Kbit,[/color] DLY 20000 usec,(高手说是带宽问题) reliability 129/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input never, output 00:00:07, output hang never Last clearing of "show interface" counters 00:11:25 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/32 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 96 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 628679 input errors, 0 CRC, 0 frame, 628679 overrun, 0 ignored, 0 abort 80 packets output, 2292 bytes, 80 underruns 80 output errors, 0 collisions, 23 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up [color=red]上面可以看出封装没有问题,但是一个高手说是带宽只有128K,无法达到2048K,是这个原因,吗?如何解决?[/color] 3、高手又看了设备版本信息如下: Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(6c), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2004 by cisco Systems, Inc. Compiled Tue 20-Jul-04 05:24 by kellythw Image text-base: 0x80008098, data-base: 0x80ED06CC cisco 2611XM (MPC860P) processor (revision 0x400) with 126976K/4096K bytes of memory. Processor board ID JPE08461048 (1510076213) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. 2 FastEthernet/IEEE 802.3 interface(s) 2 Serial(sync/async) network interface(s) [color=red]8 Low-speed serial(sync/async) network interface(s) [/color]32K bytes of non-volatile configuration memory. 32768K bytes of processor board System flash (Read/Write) 如上红字部分,高手说因为是低速端口达不到2048K带宽所致,需要更换路由器,请问是否正确?谢谢!
V35的类型多了,你使用V.35接口对接E1接口,感觉有点奇怪,建议你不要使用v35接口了,配置一个E1接口算了。至于你的带宽,根据你的CISCO路由器的V.35接口是DTE还是DCE,我估计设定的为DTE,但是也不至于只有128kbps。
建议:更换接口,直接使用E1
回答时间:2013-10-27 18:51
 
我要回应:  回应字数在5000字以内

 

热点问题