通信人家园

标题: [求助]关于X.25故障的排查  [查看完整版帖子] [打印本页]

时间:  2006-7-10 18:21
作者: mychair     标题: [求助]关于X.25故障的排查

最近我们的s1240交换机的采集出了麻烦,通过ftam登到交换机上采集话单时,采了一点,就出错终止。我们的采集链路走的是x.25协议,对通道进行误码测试,没有发现问题。采集机和交换机的相关设置检查后也没发现问题。在惠普的建议下,我对ftam的过程进行了跟踪。以下是惠普对跟踪结果的分析,认为问题出在x.25协议上,而且应该是在交换机侧。我对传输不大熟,劳驾哪位兄弟帮忙在分析以下,看能不能给一个明确的定位。谢了!
> The trace is demonstrating what I explained in my first answer: the X25 P(s) numbering is faulty at one point of time causing the FTAM connection to be closed.
>
> Here is the extract from the X25 trace:
>
> The problem seems to be on lci 2where we move from
> P(s)=6 to P(s)=5 instead of P(s)=7:
>
> Rx L3 bd: 0 p: 1 at Tue Jun 20 MESTDST 2006 10:39:00.943409 Data Packet lci 2
> Q-bit : 0 D-bit : 0 M-bit : 1
> P(R) : 5 P(S) : 5
>
> Tx L3 bd: 0 p: 1 at Tue Jun 20 MESTDST 2006 10:39:01.886409
> RR lci 2 P(R) : 6
>
> Rx L3 bd: 0 p: 1 at Tue Jun 20 MESTDST 2006 10:39:06.947409 Data Packet lci 2
> Q-bit : 0 D-bit : 0 M-bit : 1
> P(R) : 5 P(S) : 6
>
> Tx L3 bd: 0 p: 1 at Tue Jun 20 MESTDST 2006 10:39:07.896409 RR lci 2
> P(R) : 7
>
> Rx L3 bd: 0 p: 1 at Tue Jun 20 MESTDST 2006 10:39:07.901409 Data Packet lci 2
> Q-bit : 0 D-bit : 0 M-bit : 0
> P(R) : 5 P(S) : 5
>
> The problem here is we should have had:
>
> P(s)=5 to P(s)=6 to P(s)=7
>
> rather than going backward:
>
> P(s)=6 to P(s)=5
>
> So, customer needs to investigate his X25 network to understand the P(s) numbering problem and to fix it.
时间:  2006-10-7 11:31
作者: wzhj1213

X.25现在几乎都没人用了
时间:  2008-6-2 15:02
作者: wsr775     标题: 你是采集OMC资料吗?

你是采集OMC资料吗?
时间:  2008-6-2 22:00
作者: okokokokok

X.25的数据分组中P(S)称为 分组发送顺序号 ,P(R)称为 分组接收顺序号.<br/>因此,是采集器对端设备(1240或者连接1240的网络设备出了问题,发送了错误的发送顺序号)。<br/>建议检查线缆连接质量后,向沿途设备厂家报故障。<br/>




通信人家园 (https://www.txrjy.com/) Powered by C114