通信人家园

标题: [求助]谁能提供一下alcatel的7302和7300设备的详细命令手册? [查看完整版帖子] [打印本页]

时间: 2008-3-2 10:44

作者: wice 标题: [求助]谁能提供一下alcatel的7302和7300设备的详细命令手册?

<p>如题</p><p><a href="mailto:xinshixukong@sina.com">xinshixukong@sina.com</a></p>

时间: 2008-3-2 15:02

作者: 永远888

路过

时间: 2008-11-30 18:58

作者: westzwj 标题: 奶奶的

就是没人知道啊，一点点技术就藏得这么好

时间: 2009-1-16 14:21

作者: hjscj

1、 isadmin>configure>system>management# info（查看NT IP）
2、 isadmin>show# system shub entry ip（查看SHUB IP）
3、 isadmin>show# software-mngt oswp detail（查看ISAM VERSION）
4、 isadmin>show# system shub entry version detail（查看SHUB VERSION）
5、 sadmin>show>system>shub# filters shub-manager（查看指向的网管地址）
6、 Isadmin>show# atm pvc（查端口的PVC）
7、 isadmin>show>bridge# network-port detail（查看网络口的状态）
8、 isadmin>show>interface>shub# port（查看网络口的状态）
9、 isadmin>show>vlan# global（查看VLAN的数量）
10、 isadmin>show>vlan# shub-port-vlan-map（查看板卡及网络口对应的VLAN）
11、 isadmin>show>vlan# residential-bridge detail（查所有VLAN对应所带的端口）
12、 isadmin>show>bridge# port detail
13、 isadmin>show>bridge# shub-info detail（查SHUB MAC）
14、 isadmin>show>vlan# bridge-port-fdb  （查看所有VLAN获取端口MAC）
15、 isadmin>show>vlan# fdb （查看某个VLAN获取端口MAC）
16、 isadmin>show>vlan# shub-port-vlan-map（查看所有VLAN所对应的板卡及接口）
17、 isadmin>show>vlan# shub-filter-entry  (查看VLAN所获得的MAC)
18、 isadmin>show>interface>shub#vlan (显示用户VLAN及网络VLAN)
19、 show>bridge#port-to-atm-pvc  (显示桥端口与物理端口的对映关系)

时间: 2009-1-16 14:21

作者: hjscj

1．编写概述
为帮助更好维护7302ISAM设备，编写本文档。本文档所有命令以R2.2为基础，可能因为版本不同而有所变化，具体请参各个版本命令手册。
2．查看命令
2.1 端口部分
1．查看上联端口状态
isadmin># show interface shub port
============================================================
port table
============================================================
port    admin-status oper-status speed       type       duplex
--------------------------------------------------------------------------------
1       down       down       one-gb    unused    full
2       down       down       one-gb    unused    full
3       down       down       one-gb    unused    full
4       up          up       hundred-mbps network    full
5       down       down       hundred-mbps unused    full
6       down       down       hundred-mbps unused    full
7       down       down       hundred-mbps unused    full
--------------------------------------------------------------------------------
port count : 7
============================================================
解释：本命令中，admin-status指上联端口是否激活，up是激活，down是锁定
本命令中，oper-status指上联端口链路是否激活，up是激活，down是不非激活。
本命令中，speed是指上联端口的速率
本命令中，type指端口的类型，主要有：network、subtending、user等，unused表示没有配置任何类型。
本命令中，duplex指端口工作模式，主要有：full、half

2．查看用户端口状态

isadmin># show interface port xdsl-line:1/1/4/1
============================================================
port table
============================================================
port                                  admin-status opr-status
------------------------------------------------------------------------------
xdsl-line:1/1/4/1                      admin-up    down
------------------------------------------------------------------------------
port count : 1
============================================================
解释：本命令中1/1/4/1 指第4槽位第一个用户端口。7302中第4个槽位是第一块用户板，以次类推，第19个槽位是第16块用户板。第一个槽位是告警板，第二个槽位是NTA板，第三个槽位是NTB板。
本命令中，admin-status的状态指用户端口是否激活，admin-up是激活，admin-down是锁定。
本命令中，opr-status的状态指用户端是否同步，up是同步，down是不同步。

3．查看用户端口Mac地址
isadmin># show vlan bridge-port-fdb
============================================================
bridge-port-fdb table
============================================================
port                      vlan-id          mac             status
-----------------------------------------------------------------------------
1/1/4/10:8:35             2692             00:30:1b:27:11:7c learned
1/1/4/11:8:35             2693             4c:00:10:c8:7e:13 learned
1/1/4/38:8:35             2720             00:14:78:c4:f3:4d learned
1/1/4/41:8:35             2723             00:0b:2f:0b:b3:89 learned
1/1/4/43:8:35             2725             00:33:44:55:67:f0 learned
1/1/4/45:8:35             2727             00:14:78:d3:6e:d7 learned
1/1/6/2:8:35             2780             00:16:ec:bd:1b:74 learned
1/1/6/3:8:35             2781             00:17:31:b5:06:f4 learned
1/1/6/8:8:35             2786             00:a1:b0:02:33:e1 learned
1/1/6/12:8:35             2790             00:0a:eb:df:9b:b1 learned
1/1/6/14:8:35             2792             00:e0:4c:55:95:fc learned
1/1/6/15:8:35             2793             00:14:2a:39:60:4d learned
1/1/6/20:8:35             2798             00:e0:4c:72:5d:34 learned
-----------------------------------------------------------------------------
bridge-port-fdb count : 13
============================================================
解释：本命令中1/1/4/10:8:35指用户端口映射的bridge port，vlan-id指用户端口绑定的vlan号，mac指7302学习到的用户PC的Mac地址，该Mac地址只要用户打开PC，Modem同步后即能学习到。

4．查看用户Bridge端口信息
isadmin># show bridge port
================================================================================
port table
================================================================================
port             bridge-port pvid          default-priority qos-profile
                                       status
--------------------------------------------------------------------------------
1/1/4/1:8:35    33       2683          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/2:8:35    34       2684          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/3:8:35    35       2685          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/4:8:35    36       2686          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/5:8:35    37       2687          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/6:8:35    38       2688          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
1/1/4/7:8:35    39       2689          0             00:00:00:00:00:0
0:00:00:00:00:00:00:00:00:00:00:00:00:00 static
port count : 7
================================================================================
解释：本命令中，bridge-port是7302根据用户端PVC自动映射的，pvid是强制给用户端不带VLAN信息的帧打上的VLAN Tag标记，default-priority是QoS标记。

2.2  系统部分
1. 查看板卡状态
isadmin># show equipment slot
============================================================
slot table
============================================================
slot          actual-type enabled error-status          availability
-----------------------------------------------------------------------------
1/1/1       aacu-c    yes    no-error             available
1/1/2       ecnt-a    yes    no-error             available
1/1/3                   no    no-error             not-installed
1/1/4       eblt-a    yes    no-error             available
1/1/5       eblt-a    yes    no-error             available
1/1/6       eblt-a    yes    no-error             available
1/1/7       eblt-a    yes    no-error             available
1/1/8                   no    no-error             not-installed
1/1/9                   no    no-error             not-installed
1/1/10                   no    no-error             not-installed
1/1/11                   no    no-error             not-installed
1/1/12                   no    no-error             not-installed
1/1/13                   no    no-error             not-installed
1/1/14                   no    no-error             not-installed
1/1/15                   no    no-error             not-installed
1/1/16                   no    no-error             not-installed
1/1/17                   no    no-error             not-installed
1/1/18                   no    no-error             not-installed
1/1/19                   no    no-error             not-installed
-----------------------------------------------------------------------------
slot count : 19
============================================================
解释：本命令中，slot是板卡槽位，actual-type是板卡类型，enabled是板卡管理状态，正常情况下为yes；error-status是错误状态，正常情况下为no-error，非正常状态有board-missing、board-mismatch等。availability是板卡启用状态，正常情况下为available，非正常状态有init-failure等，板卡刚启动时显示为in-test。

2．查看NT软件版本
isadmin># show software-mngt oswp
============================================================
oswp table
============================================================
index name                            availability act-status commit-status
-------------------------------------------------------------------------------
1    L6GPAA22.418                   enabled    active    committed
2    NO_OSWP                         empty       not-active un-committed
-------------------------------------------------------------------------------
oswp count : 2
============================================================
解释：本命令中act-status为active的为当前在用版本。
3．查看SHUB软件版本
isadmin># show system shub entry version
============================================================
version table
============================================================
         sw-ver-name : LANX
      sw-release-num : 1.0.0.1
            hw-ver : H/WVersion1
            fw-ver : LANX_R2.2.11.1
============================================================
解释：本命令中，SHUB软件版本为R2.2.11.1
2.3  告警部分
isadmin># show alarm current table
==============================================
table table
==============================================
index    type          last-updated-on
----------------------------------------------
----------------------------------------------
table count : 0
==============================================
解释：查看当前告警，现用本命令查看告警分类，本例中无告警。一般告警分类有：equipment
eqpt-holder、plug-in-unit、atm、ether-itf、sw-mgmt、xdsl、tca-xdsl、eo-conversion、authentication
、bonding-group、redundancy、custom等。
如要看具体告警内容，需要进一步的命令，如：
isadmin># show alarm current equipment
============================================================
equipment table
============================================================
index    persist-data sntp-comm nt-disk             connection-lost
------------------------------------------------------------------------
------------------------------------------------------------------------
equipment count : 0
============================================================
3．配置命令
3.1 管理IP地址配置
isadmin># configure system management
isadmin>configure>system>management# info
configure system
#------------------------------------------
echo "system"
#------------------------------------------
management
  host-ip-address manual:222.184.77.225/24
  default-route 222.184.77.1
  exit
exit
#------------------------------------------
如要修改IP地址，可以直接修改。

3.2线速模板配置
配置线速模板
isadmin># configure xdsl service-profile 1 name 2M-640K-Fast
isadmin>#configure xdsl service-profile 1 min-bitrate-up 64 min-bitrate-down 64 plan-bitrate-up 640 plan-bitrate-down 2048 max-bitrate-up 640 max-bitrate-down 2048 max-delay-up 1 max-delay-down 1 active
配置协议模板
isadmin># configure xdsl spectrum-profile 1 name adsl
isadmin>#configure xdsl spectrum-profile 1 active
默认状态打开如下协议：
协议名称说明
ansi-t1413 ANSI T1.413-1998
etsi-dts ETSI DTS/TM06006
g992-1-a ADSL G.dmt over POTS
g992-1-b ADSL G.dmt over ISDN
g992-2-a ADSL G.lite
g992-3-a ADSL2 over POTS
g992-3-b ADSL2 over ISDN

   注：R2.2版本中如果需要打开ADSL2+等协议需要单独定义
R2.2.03中允许修改Spectrum-Profile
isadmin># configure xdsl spectrum-profile 1 modification start g992-5-a
isadmin>configure>xdsl>spectrum-profile>1# modification complete
附： Multi-ADSL Modes of Operation

G.992.1 ADSL G.dmt
G.992.2 ADSL G.lite
G.992.3 Annex A ADSL2 operation over POTS non-overlapped spectrum
G.992.3 Annex L READSL2 operation over POTS non-overlapped spectrum US masks
G.992.5 Annex A ADSL2+ operation over POTS non-overlapped spectrum
G.992.3 Annex M ADSL2 operation over POTS with extended upstream bandwidth
G.992.5 Annex M ADSL2+ operation over POTS with extended upstream bandwidth

登陆帐号：isadmin
登陆密码  ans#150

端口表示方法：1/1/槽号/端口号

1) 查看模板配置命令：
Show>xdsl# info configure xdsl service-profile
2) 查看端口线路模板配置命令：
Show>xdsl# info configure xdsl line 1/1/slot/port
3) 更改端口的模板配置命令：
isadmin>#Configure xdsl line 1/1/slot/port service-profile 1 spectrum-profile 2 admin-up
4) 根据mac查端口
isadmin># Show vlan fdb mac  xx：xx：xx：xx：xx：xx
5) 显示所有单板
show equipment slot
6) 查看端口激活情况：
isadmin># show interface port xdsl-line:1/1/4/1 (单个端口)
isadmin># show interface port xdsl-line:1/1/4/[1...48] （查看该板卡所有端口）
端口表示方法：1/1/槽号/端口号

1）查看模板配置命令：
Show>xdsl# info configure xdsl service-profile
2) 查看端口线路模板配置命令：
Show>xdsl# info configure xdsl line 1/1/slot/port
3)更改端口的模板配置命令：
Configure xdsl line 1/1/slot/port service-profile 1 spectrum-profile 2 admin-up
4根据mac查端口
Show vlan fdb mac  xx：xx：xx：xx：xx：xx

显示所有单板：show equipment slot

查看端口激活情况：show atm pvc 1/1/槽号/端口号:0:35
注：当要查看多个端口或槽位时，可用[x…y]表示范围

打死激活端口
lock端口和unlock端口

1.configure xdsl line  1/1/4/1 no admin-up
2.configure xdsl line  1/1/4/1 admin-up

查看设备配置的速率模板及对应的index号：

isadmin># info configure xdsl service-profile

查看当前某个端口具体的配置的速率：

isadmin># info configure xdsl  line 1/1/4/1

批量修改端口速率

configure xdsl line 1/1/4/[1...48] service-profile 3 spectrum-profile 1 admin-up

查看当前具体某个端口的状态

isadmin># show interface port xdsl-line:1/1/4/27
======================================================================
port table
======================================================================
port                            admin-status opr-status
--------------------------------------------------------------------------------
xdsl-line:1/1/4/27             admin-up    down
--------------------------------------------------------------------------------
port count : 1
======================================================================

文件结束
End of file

时间: 2009-3-4 11:00

作者: waxberry520

这2个设备属于要淘汰的设备了！！MS有专门的网管可以的！！！

时间: 2009-11-5 13:46

作者: tomtuo

http://www.txrjy.com/viewthread.php?tid=267053&page=1#pid2667463

时间: 2009-11-6 13:03

作者: tlist 标题: 请教各位大侠，这个DSLAM是什么型号的

请教各位大侠，这个DSLAM是什么型号的（品牌应该是贝尔或者alcatel）：

<XXX_5200G>te v DSLAM-wangguan 1XX.XX.XX.68
Trying 1XX.XX.XX.68 ...
Press CTRL+T to abort
Connected to 1XX.XX.XX.68...
user name: isadmin

user password:
password is incorrect

user name: f
user password:
password is incorrect

user name: c
The connection was closed by the remote host!
<XXX_5200G>

ARP信息
1XX.XX.XX.68 0007-724f-f15d 30 D DSLAM-wangguan Eth-T2/0/0.30

时间: 2009-12-18 16:32

作者: 增C添翼

5200G是华为的设备吧

通信人家园 (https://www.txrjy.com/)