1、GEM_MA5600(config)#display interface mEth 0
会显示以下信息:
meth0 current state : UP
Line protocol current state : UP
Description : HUAWEI, MA5600 Series, MEth0 Interface
The Maximum Transmit Unit is 1500 bytes
Internet Address is 10.11.104.2/16
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc8a-5f93
Auto-duplex(Full), Auto-speed(100M)
5 minutes input rate 42 bytes/sec, 0 packets/sec
5 minutes output rate 13 bytes/sec, 0 packets/sec
191 packets input, 19356 bytes
127 packets output, 8996 bytes
此步要求工程师所用电脑的IP地址与MA5600在同一地址段，电脑和设备之间能正常通信。举例：电脑IP地址设为：10.11.104.3
2,GEM_MA5600(config)#backup data tftp 10.11.104.3 rlvld090.dat
//此处只需要更改rlvld090.dat,这个是你升级的那台MA5600数据库文件备份，举例：锡盟网通中心局有台5600，现在版本为B02D090，你备份是就可以命名为：xmzxjd090.dat
//在备份数据库时可以使用display progress backup 来查看备份进度，如：
GEM_MA5600(config)#display progress backup
FrameID/SlotID: 0/7
Board name: H561SCU
Operation type: Backup
File type: Host data
Operation phase: Transfer file from inside to outside
Rate of process: 100%
3,GEM_MA5600(config)#load packetfile tftp 10.11.104.3 scuv3r2b02d105_packet.bin active
//执行上面命令后会出现“…… Are you sure to load new packet file? (y/n)[n]:”，请选择y
//此处scuv3r2b02d105_packet.bin为升级要达到的软件版本. 注意：升级软件的版本一定要是办事处正式确认下来的!!!
//在加载主程序时可以使用display progress load 来查看加载进度，如：
GEM_MA5600(config)#display progress load
FrameID/SlotID: 0/7
Board name: H561SCU
Operation type: Load
File type: Packet file
Operation phase: Saving file
Rate of process: 95%
4、升级所需的主程序文件加载完成后，使用display io-packetfile information命令查看主程序是否加载成功
GEM_MA5600(config)#display io-packetfile information
-------------------------------------------------------------------
Index File Type Version File Length
-------------------------------------------------------------------
0 H565ADEF PROGRAM V300R002B02D105 1050880
1 H565ADEF BIOS V300R002B03D005 182144
2 H565ADBF PROGRAM V300R002B02D105 1050880
3 H565ADBF BIOS V300R002B03D005 182144
4 H563ADGG PROGRAM V300R002B02D105 967168
5 H563ADGG BIOS V300R002B03D005 182400
6 H563ADEF PROGRAM V300R002B02D105 973312
7 H563ADEF BIOS V300R002B03D005 182400
8 H561SHEA PROGRAM V300R002B02D105 844416
9 H561SHEA BIOS V300R002B03D005 182144
10 H561AIUG PROGRAM V300R002B02D087 1288832
11 H561AIUG BIOS V300R002B02D104 258176
12 H561ADBF PROGRAM V300R002B02D105 880896
13 H561ADBF BIOS V300R002B03D005 183808
-------------------------------------------------------------------
4、利用“华为数据库升级工具”将你第2步备份出来的数据库文件rlvld090.dat升级到与要达到的新版本一致的数据库文件rlvld105.dat
5、GEM_MA5600(config)#load data tftp 10.11.104.3 rlvld105.dat active
//该步骤完成升级后数据库文件rlvld105.dat的加载
//执行上面命令后会出现“…… It's irreversible. Are you sure to load new database? (y/n)[n]:”，请选择y
6、GEM_MA5600(config)#reboot system
//执行上面命令后会出现“ Please check whether data has saved, the unsaved data will lose if reboot system, are you sure to reboot system? (y/n)[n]:”，请选择y
出现“File(Active MainBoardata)has been updated,please check whether the file is loaded correctly,are you sure to reboot ? (y/n)[n]:”，请选择y
===========================================
ata)has been updated,please check whether the file is loaded correctly,are you sure to reboot ? (y/n)[n]:”，请选择y