通信人家园

标题: ZTE C300设备上行业务卡无法配置 [查看完整版帖子] [打印本页]

时间: 2016-4-1 10:01

作者: sgztetest 标题: ZTE C300设备上行业务卡无法配置

有谁知道我的C300设备为什么无法配置上行业务卡？具体信息如下：
C300(config)#show version-running
PhyLoc  FileType VerType VerTag          BuildTime          VerLenth
--------------------------------------------------------------------------------

1/1/3 GTGOG    MVR       V1.2.3P3       2013-05-10 02:40:05 4646872
1/1/3 PM       FW       V1.2.3P3       2013-01-23 08:13:47 934
1/1/3 GTGOG    BT       V4.0.0          2014-01-17 11:01:46 524288
1/1/10  SCXM    MVR       V1.2.3P3       2013-02-04 03:56:48 8611395
1/1/10  SCXM    BT       V1.2.3          2012-06-06 13:10:39 447632
1/1/11  SCXM    MVR       V1.2.3P3       2013-02-04 03:56:48 8611395
1/1/11  SCXM    BT       V1.2.3          2012-06-06 13:10:39 447632
1/1/21  GUCD    MVR       V1.2.3P3       2013-01-23 02:05:35 1933221
1/1/21  GUCD    BT       V1.2.1          2011-09-07 12:08:39 223924
1/1/22  GUCD    MVR       V1.2.3P3       2013-01-23 02:05:35 1933221
1/1/22  GUCD    BT       V1.2.1          2011-09-07 12:08:39 223924
C300(config)#show card
Rack Shelf Slot CfgType RealType Port  HardVer SoftVer       Status
-------------------------------------------------------------------------------
1 1    0          PRWG    0                            HWONLINE
1 1    1          PRWG    0                            HWONLINE
1 1    3 GTGO GTGOG 8    120301  V1.2.3P3       INSERVICE
1 1    10 SCXM SCXM    0    090700  V1.2.3P3       STANDBY
1 1    11 SCXM SCXM    0    090700  V1.2.3P3       INSERVICE
1 1    21 GUFQ GUFQ    4    090200  V1.2.3P3       INSERVICE
1 1    22 GUFQ GUFQ    4    090200  V1.2.3P3       INSERVICE

C300(config)#show interface gei_1/21/1 //这个端口显示的信息为什么是"inner-port_1/20/2 ", 似乎所有端口显示的信息都是一样的？
inner-port_1/20/2 is down,  line protocol is down
  Description is none
  Keepalive set:10 sec
  The port is optical
  Duplex full
  scramble payload-enable
  VLAN mode is hybrid, pvid 1
  Last clearing of "show interface" counters never
120 seconds input rate :                0 Bps,             0 pps
120 seconds output rate:                0 Bps,             0 pps
  Interface peak rate  :
input                   0 Bps, output                   0 Bps
  Interface utilization: input    none,    output    none
  Input:
Packets       : 0                      Bytes       : 0
Unicasts       : 0                      Multicasts    : 0
Broadcasts    : 0                      Undersize    : 0
Oversize       : 0                      CRC-ERROR    : 0
Dropped       : 0                      Fragments    : 0
Jabber          : 0                      MacRxErr    : 0
IncorrectVlanDrop: 0
  Output:
Packets       : 0                      Bytes       : 0
Unicasts       : 0                      Multicasts    : 0
Broadcasts    : 0                      Collision    : 0
LateCollision : 0                      SingleCollision: 0
MultCollision : 0                      Dropped       : 0
  Input detail:
64B             : 0                      65-127B       : 0
128-255B       : 0                      256-511B    : 0
512-1023B       : 0                      1024-2047B    : 0
C300(config-if)#show interface port-status gei_1/21/1
-----------------------------------------------------------------------------
Port hybrid  Native Negotiation  Speed  Duplex Flow- Admin    Link
         Status  VLAN    auto    (Mbps)       Ctrl Status
-----------------------------------------------------------------------------
gei_1/21/1  optical  1    enable    auto full  disable activate down
C300(config-if)#hybrid-attribute copper //这个设置也失败了
%Code 37939: MsPort:unsuportted interface or invalid port id.
C300(config-if)#switchport mode hybrid
%Code 30515: Invalid parameter.//这个设置也失败了
请哪位达人帮忙解决一下？谢谢了。

时间: 2016-4-6 15:07

作者: sgztetest

原因已经找到了，是配置rack的时候没有选对rack的型号，应该用的是19的型号。

通信人家园 (https://www.txrjy.com/)