- 经验
- 39
- 分贝
- 0
- 家园分
- 189
- 在线时间:
- 99 小时
- 最后登录:
- 2020-10-18
- 帖子:
- 32
- 精华:
- 0
- 注册时间:
- 2015-10-16
- UID:
- 1161944
注册:2015-10-167
|
本帖最后由 jeff.chiu 于 2017-3-6 15:57 编辑
!
pon
onu-type BCM68380 gpon
onu-type BCM68380 gpon max-tcont 8
onu-type BCM68380 gpon max-gemport 32
onu-type BCM68380 gpon max-iphost 0
onu-type BCM68380 gpon max-veip 1
onu-type-if BCM68380 pots_0/1
onu-type-if BCM68380 pots_0/2
uncfg-onu-display-info model sn pw
!
pon
onu-profile gpon BCM68380
vport-mode manual def-map-type vlan
tcont 1 profile 100M
gemport 1 tcont 1
vport 1 map-type vlan
vport-map 1 1 vlan 10
remote
service 1 gemport 1 vlan 10
vlan port veip_1 mode trunk
vlan port veip_1 vlan 10
ex-vlan veip 1 input-tpid 0x8100 output-tpid 0x8100 down-mode inverse-upstream
!
interface gpon-olt_1/2/1
no shutdown
linktrap disable
onu 2 type BCM68380 sn BCDM17050004
onu 2 profile BCM68380
!
interface gpon-onu_1/2/1:2
switchport mode trunk vport 1
service-port 1 vport 1 user-vlan 10 vlan 500
dhcpv4-l2-relay-agent trust true replace vport 1
!
想請問 為什麼我下了這個指令,最後下發出來給BCM68380的extending vlan還是上下傳不對稱的?
下傳是不正常的 沒有filter 沒有action 就是完全透通
<4>VLAN Rule Table : gpon0.0, Rx, nbrOfTags 1, default DROP
<4>
<4>--------------------------------------------------------------------------------
<4>===> gpon0.0 (ONT) : RX, 1 tag(s)
<4>Tag Rule ID : 0
<4>Rx VLAN Device : veip0
<4>
<4>Filters
<4> VlanDev MacAddr : No
<4>
<4>Commands
<4> 00:[NOP, 0x00000000, 0x00000000]
<4>
<4>Rule Type : Flow
<4>Hit Count : 1217
<4>
<4>--------------------------------------------------------------------------------
這是上傳的 是正常的
<4>VLAN Rule Table : gpon0.0, Tx, nbrOfTags 1, default DROP
<4>
<4>--------------------------------------------------------------------------------
<4>===> gpon0.0 (ONT) : TX, 1 tag(s)
<4>Tag Rule ID : 0
<4>Rx VLAN Device : DEFAULT
<4>
<4>Filters
<4> Rx REALIF :
<4> Tx VLANIF : veip0
<4> VLAN Tag 0 : pbits -, cfi -, vid 10, (tci 0x0FFF/0x000A), ether -
<4>
<4>Commands
<4> 00:[NOP, 0x00000000, 0x00000000]
<4>
<4>Rule Type : Flow
<4>Hit Count : 622
<4>
<4>--------------------------------------------------------------------------------
因為類似配置在華為MA5600T、ALU 7360都是正常對稱的,不知道為什麼中興的不會對秤
是否少了甚麼配置?
|
|