Step 11 Configure the asynchronous serial lines for the integrated modems on the modules installed in the access server. (If you want to allow users to dial in through the integrated modems, you must configure the async lines.)
Async lines accept incoming modems calls. If you will have users dialing in via modems, configure these lines.
Configure Async lines? [yes]:
Note We recommend that you do not change the async line speed for modems. However, for V.110 terminal adapters, we recommend that the speed not go above 19200.
Note If your asynchronous interfaces will be using the same basic configuration parameters, we recommend that you group them so that they can be configured as a group. Otherwise, you will need to configure each interface separately.
Note Dynamic IP addresses permit dial-in users to choose a static IP address when they dial in. If you do not allow dynamic IP addresses, the access server will provide IP addresses from an IP address pool that you set up later in the next prompt.
Allow dial-in users to choose a static IP address? [no]:
Configure for TCP header compression? [yes]:
Configure for routing updates on async links? [no]:
Enter the starting address of IP local pool? [X.X.X.X]: 172.20.30.40
Enter the ending address of IP local pool? [X.X.X.X]: 172.20.30.88
You can configure a test user to verify that your dial-up service is working properly.
What is the username of the test user? [user]:
What is the password of the test user? [passwd]:
Will you be using the modems for outbound dialing? [no]:
Configure for Async IPX? [yes]: no
Configure for Appletalk Remote Access (ARA)? [no]: yes
AppleTalk Network for ARAP clients [1]:
Zone name for ARAP clients [ARA Dialins]:
Allow ARAP "Guest" logins? [yes/no]: yes
Step 12 Enter the letter corresponding to the ISDN switch type that matches your telco switch type or press Enter to accept the default:
Do you want to configure ISDN switch type? [yes]:
The following ISDN switch types are available:
[a] primary-4ess primary-5ess
[c] primary-dms100
[d] primary-net5
[e] primary-ntt
[f] primary-ts014
Enter the switch type :
Step 13 Press Enter to allow users to dial in via ISDN or analog modems:
Next, you will be prompted to configure controllers.
These controllers enable users to dial in via ISDN or analog modems.
Do you intend to allow users to dial in? [yes]:
There are 8 controllers on this access server. If you want to use
the full capacity of the access server configure all controllers.
Controller T1 0,1,..etc in software corresponds to Port 0,1,..etc
on the back of the access server.
PRI configuration can be configured to controllers all at once
based on your PRI controllers selection. Where as CAS configuration
will be configured individually for each controller.
Step 14 Enter the number of controllers you will be using for the PRI configuration or press Enter to configure all controllers:
Enter # of controllers, you will be using for PRI configuration [8]:
Configuring controller parameters:
Step 15 Set the CAS configuration options for the first controller you are configuring. First, press Enter to set robbed-bit signaling on the controller:
Configuring controller T1 2:
Will you be using CT1 (robbed bit signaling) on this controller? [yes]:
Step 16 Enter your telco framing type:
The following framing types are available: esf | sf
Enter the framing type [esf]:
Step 17 Enter your telco line code type:
The following linecode types are available: ami | b8zs
Enter the line code type [b8zs]:
Step 18 Enter the letter corresponding to the signaling type to support modem pooling over the T1 lines or press Enter to accept the default:
The following line signaling types are available:
[a] e&m-fgb e&m-fgd
[c] e&m-immediate-start
[d] fxs-ground-start
[e] fxs-loop-start
[f] sas-ground-start
[g] sas-loop-start
Enter the line signaling type [a]:
Step 19 Enter the tone signaling type:
The following tone signaling types are available: dtmf | mf
Enter the tone signal type [dtmf]:
Step 20 Press Enter to configure digital number identification service (DNIS) over T1 lines:
Do you want to provision DNIS address information? [yes]:
Step 21 Repeat Step 15 to Step 20 to configure the remaining controllers.
Step 22 Enter yes to configure the Ethernet 0 interface (this is the Ethernet 10BaseT port) if you plan to use this interface to manage and monitor the access server:
Configuring interface parameters:
Do you want to configure Ethernet0 interface? [no]: yes
Configure IP on this interface? [no]: yes
IP address for this interface: 172.21.40.10
Subnet mask for this interface [255.0.0.0] :
Class B network is 172.21.0.0, 16 subnet bits; mask is /16
Configure LAT on this interface? [no]:
Configure AppleTalk on this interface? [no]:
Configure IPX on this interface? [no]:
Step 23 Press Enter or enter yes to configure the Fast Ethernet 0 interface (this is the Ethernet 100BaseT port) to connect the access server to a LAN:
Do you want to configure FastEthernet0 interface? [yes]: yes
Operate in full-duplex mode? [no]: yes
Operate at 100 Mbps speed? [yes]:
Configure IP on this interface? [yes]:
IP address for this interface [X.X.X.X]: 172.22.50.10
Subnet mask for this interface [255.255.0.0] :
Class B network is 172.22.0.0, 16 subnet bits; mask is /16
Configure LAT on this interface? [no]:
Configure AppleTalk on this interface? [no]:
Configure IPX on this interface? [no]:
Step 24 Configure your serial intefaces by responding to the following prompts:
Do you want to configure Serial0 interface? [no]: yes
Note If using the serial interfaces to route data from the T1/PRI or E1/PRI ports to a WAN, you need to configure IP on the interface. Enter the IP address of the WAN device to which the data will be routed.
Configure IP on this interface? [no]: yes
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 173.20.30.40
Subnet mask for this interface [255.255.0.0] :
Class B network is 173.20.0.0, 16 subnet bits; mask is /16
Configure LAT on this interface? [no]:
Configure AppleTalk on this interface? [no]:
Configure IPX on this interface? [no]:
Step 25 Repeat Step 24 to configure the other three serial interfaces, if necessary.
Step 26 Configure the PRI D-channel (signaling channel):
Do you want to configure Serial0:23 (PRI D-channel) interface? [no]: yes
Configure IP on this interface? [no]: yes
Configure IP unnumbered on this interface? [no]:
IP address for this interface: 173.20.30.40
Subnet mask for this interface [255.255.0.0] :
Class B network is 173.20.0.0, 16 subnet bits; mask is /16
Configure LAT on this interface? [no]:
Configure AppleTalk on this interface? [no]:
Configure IPX on this interface? [no]:
Step 27 Repeat Step 26 for each D-channel.
After you complete the configuration script, messages similar to the following appear.
The following configuration command script was created:
hostname 5300
enable secret 5 $1$WVLB$YD0zbQsu3nqZh/bnN2fwX0
enable password guessme
line vty 0 4
password guessagain
syscon shelf-id 0
syscon address 172.87.98.1 sctest
snmp-server community public
!
appletalk routing
no decnet routing
no ip routing
no clns routing
ipx routing
no vines routing
no xns routing
no apollo routing
!
line 1 120
speed 115200
flowcontrol hardware
login local
autoselect during-login
autoselect ppp
modem dialin
ip local pool setup_pool 172.20.30.40 172.20.30.88
!
username user password passwd
!
arap network 1 ARA Dialins
line 1 120
arap enable
autoselect arap
!
! Turn off IPX to prevent network conflicts.
interface Ethernet0
no ipx network
interface FastEthernet0
no ipx network
interface Serial0
no ipx network
interface Serial1
no ipx network
interface Serial2
no ipx network
interface Serial3
no ipx network
interface Serial0:23
no ipx network
interface Serial1:23
no ipx network
interface Serial2:23
no ipx network
interface Serial3:23
no ipx network
!
isdn switch-type primary-5ess
!
controller T1 0
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 1
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 2
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 3
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 4
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 5
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 6
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
!
controller T1 7
no shutdown
framing esf
linecode b8zs
cas-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
scheduler interval 1000
line console 0
logging synchronous
!
interface Ethernet0
no shutdown
ip address 172.21.40.10 255.255.0.0
no lat enabled
no mop enabled
!
interface FastEthernet0
duplex full
speed 100
ip address 172.22.50.10 255.255.0.0
no lat enabled
no mop enabled
!
interface Serial0
no shutdown
ip address 173.20.30.40 255.255.0.0
no lat enabled
no mop enabled
!
interface Serial1
shutdown
no ip address
!
interface Serial2
shutdown
no ip address
!
interface Serial3
shutdown
no ip address
!
interface Serial0:23
no shutdown
no ip address
no lat enabled
no mop enabled
!
interface Serial1:23
no shutdown
ip address 173.20.30.40 255.255.0.0
no lat enabled
no mop enabled
!
interface Serial2:23
no shutdown
no ip address
no lat enabled
no mop enabled
no shutdown
no ip address
no lat enabled
no mop enabled
!
Interface Group-Async1
group-range 1 120
ip unnumbered FastEthernet0
encapsulation ppp
ppp authentication chap pap
peer default ip address pool setup_pool
ip tcp header-compression passive
async mode interactive
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
end
end
Step 28 Enter 0, 1, or 2 when the following prompt is displayed:
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]:
Use this configuration? [yes/no]: yes
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINK-3-UPDOWN: Interface Serial1, changed state to down
<Additional messages omitted.>
Step 29 When the messages stop displaying on your screen, press Enter to get the following prompt:
5300>
%AT-6-ONLYROUTER: Ethernet0: AppleTalk port enabled; no neighbors found
Step 30 The 5300> prompt indicates that you are now at the command-line interface (CLI) and you have just completed the basic access server configuration. However, this is not a complete configuration. At this point you have two options:
Run the setup script in the System Configuration dialog again and create another configuration. Enter the following commands to repeat the setup script:
5300> enable
Password: <password>
5300# setup
Modify the existing configuration or configure additional features with the CLI as described in the Dial Solutions Configuration Guide, the Dial Solutions Command Reference Guide the Cisco IOS software configuration guide, and command reference publications.
发表于 2008-1-9 18:55:00